Welcome To TianYun Group Co., Ltd.
TianYun Group

A Professional Rubber, Plastics and New Material Manufacturer

Industry News

HomeIndustry News
Why Does Nylon Sheet Absorb Moisture and Change Size?
2026-11-05 22:23:43

Why Does Nylon Sheet Absorb Moisture and Change Size?

Introduction: Nylon sheet absorbs moisture because its semi-crystalline structure contains amorphous regions that attract water, and that water can shift machined dimensions.

A freshly machined nylon part can pass inspection and still change slightly after a humid weekend or a few days in storage. That small movement matters in bearing seats, bushings, slide plates, and close-fitting assemblies where clearance is tight. this guide follows the cause chain from polymer structure to moisture movement, then to machining and final fitting. It also explains how to read water absorption figures without turning a useful grade number into an impossible stability promise.

How Water Molecules Move Through Semi-Crystalline Nylon

Nylon is a polyamide, and its backbone contains polar amide groups. Water molecules are also polar, so they are attracted to those groups. In a dry part, polymer chains hold together through hydrogen bonding. When moisture enters, water competes for hydrogen-bond sites and pushes chains slightly apart. That is the first link in the dimensional chain: water uptake changes the spacing and mobility of polymer chains, and the part responds with a small volume change. The movement is gradual because moisture has to travel through the polymer rather than simply wetting the surface.

1. Amorphous Regions Take In Moisture While Crystalline Regions Resist It

Semi-crystalline nylon has two kinds of morphology. Crystalline regions are ordered, tightly packed, and relatively resistant to water penetration. Amorphous regions are disordered, with more free volume and more exposed amide groups, so moisture gathers there first. The crystalline regions act like a framework that gives the sheet strength and creep resistance, while the amorphous regions carry much of the moisture-related movement. Polymer science teaching resources from Cambridge describe this two-phase picture: ordered crystalline lamellae sit within a less ordered amorphous phase, and the amorphous phase responds more readily to small molecules such as water. A higher crystallinity grade tends to take up less water and move less, but ordinary nylon sheet still has enough amorphous content to respond to humidity. This is why a dry-looking sheet can gain moisture from ordinary shop air; the water is inside the polymer structure, not sitting on the surface as a visible film.

2. Part Thickness and Humidity History Change the Pace of Dimensional Drift

Moisture does not appear evenly through a thick nylon sheet at once. The surface reaches a new moisture level first, while the core follows more slowly. A thin strip may come close to equilibrium in a short time, while a thick block can keep changing for much longer. Humidity history matters in the same way. A sheet stored in a dry warehouse and then moved into a humid machining area starts with a moisture gradient. A sheet already conditioned near the service humidity has less room to change. The practical result is that two parts made from the same grade can behave differently if their thickness, storage history, or shop humidity differs. Process engineers see this as a slow drift in fit, not a sudden jump. Thick sections and parts with one exposed face are especially likely to show a delayed change because moisture reaches one side before the other.

Why Dimensional Change Appears After Machining and Fitting

Machining turns a sheet into a part with new surfaces, thin walls, holes, and pockets. Those features change how moisture enters and how the part responds. A freshly cut surface exposes new polymer to shop air, and a thin wall can pick up moisture faster than the original block. A common workshop pattern is that a batch checks well right after machining, then final fitting checks reveal small changes after humid storage. The hole may close slightly, a bushing may grow, or a long plate may bow if one face absorbs moisture faster than the other. These movements are small, but precision fits do not need a large movement to create a tight spot or a rattle. A part that was dimensionally correct when dry can behave differently once it reaches the moisture level of the assembly area. The timing of measurement belongs in the process plan. If a part is measured dry and then assembled in a humid plant, the fit condition at assembly can differ from the inspection condition. If a part is measured after a few hours in air, it may still be far from its long-term moisture level. The useful approach is to define the moisture state that matters for the application, then measure and fit under conditions that represent it. For some parts, that means checking after a stabilization period in the production environment. For others, it means designing clearance for the expected humidity range. Nylon sheet is machinable and widely used for bushings, wear pads, and insulators, so this is a normal part of working with the material rather than a defect in the sheet. The key is to treat moisture as a process variable from the first cut to the final fit check.

How to Read Water Absorption Figures Without Overpromising Stability

Water absorption figures are useful, but they need context. Some data report 24-hour immersion, some report saturation, and some report equilibrium at a stated relative humidity. A 24-hour number and a saturation number describe different states, so comparing them directly can mislead. The rate of pickup and the final moisture content also depend on temperature and the surrounding air. The 10100 NYLON Sheets range covers PA6, PA66, and glass-filled grades, and its material data gives water absorption around 1.0% to 3.0% or higher depending on grade. That range is a material-level guidepost. Exact size change still depends on grade, thickness, humidity, and time. A specifier who treats the number as a fixed dimensional correction is asking it to do more than it can. A lower water absorption figure is helpful because it points to slower or smaller moisture pickup under the stated test. The number describes moisture pickup under a defined condition; permanent dimensional stability requires more than a low figure. Nylon remains hygroscopic, and a change in humidity can still move a precision fit. Claims of zero water absorption, 100% waterproofing, or guaranteed zero dimensional change are a warning sign for ordinary nylon sheet. The better message is narrower and more useful: choose the grade for the service environment, define the moisture condition for machining and inspection, and allow for the small dimensional movement that moisture can create. A nylon sheet supplier that explains those conditions is more useful than one that promises perfect stability. Measurement practice matters too; metrology guidance such as NIST's work on traceable methods and defined conditions supports the same principle of comparing like with like.

Conclusion

Nylon sheet absorbs moisture because water enters the amorphous regions of its semi-crystalline structure and interacts with polar amide groups. The result is a small, time-dependent dimensional change that becomes visible in precision machining, storage, and final fitting. Thickness, humidity history, and the moisture state at measurement all shape how quickly that change appears. The practical takeaway is not to fear nylon sheet, but to treat moisture as a normal design and process variable. Use grade data as a starting point, define the humidity condition that matters, and avoid any supplier promise of zero water absorption or zero swelling. Readers who want to compare the published range for PA6, PA66, and glass-filled nylon grades can review the 10100 NYLON Sheets material data.

FAQ

Q: Why does a PA6 nylon sheet absorb moisture even when it feels dry?

A: PA6 nylon is hygroscopic at the polymer level. Water molecules bond to polar amide groups in the amorphous regions, so moisture can enter the sheet from ordinary air without leaving a wet film on the surface. The sheet feels dry because the water is inside the polymer structure, not because the material is waterproof.

Q: How does water absorption affect machining tolerance in nylon parts?

A: Moisture uptake changes the spacing and mobility of polymer chains, so a machined feature can grow or lose clearance after the part absorbs water. The effect is gradual and depends on thickness, shop humidity, storage time, and the measurement condition. Precision parts need a defined moisture state for machining, inspection, and fitting rather than a single dry measurement.

Q: Does a lower water absorption number mean a nylon sheet will never change size?

A: No. A lower number means less or slower moisture pickup under the stated test, while nylon remains sensitive to humidity changes. Exact movement depends on grade, thickness, environment, and time. Treat published water absorption as a comparison guide and plan for the humidity range the part will actually see.

Sources / References

Crystallinity in Polymers

National Institute of Standards and Technology

Related Examples

10100 NYLON Sheets



Contact Us
  • Contact:Conrad

  • Tel: +8618740270933

  • Whatsapp:+8618740270933

  • E_mail: info@tianyungroup.net